Creating Display Dioramas Accessories For Your Action Figures

Posted by Unknown on 5:00 PM in accessories, Action, Creating, Dioramas, Display, Figures, For, your | No comments

We regularly ask for tips, article ideas and general info from guys and gals just like you!  Recently, we were send this article. For the full article scroll to the bottom and hit the link.

This is just an opinion post about what you may try to do yourself. We are not responsible for any loss, injury, theft, etc. regarding any of the tips in this post.

Making an Oil Drum

• Take a 14 ounce can and remove the top and label. 
• Use one of the new Euro-Openers that cut from the side for best results. Eat contents and clean can. Dry well. Using a hot glue gun, glue the top back on. 
• Hot glue a 1/4" hex nut to the top near the edge and fill in the hole with glue. 
• Spray the can one of 3 colors: sage green, battleship gray or mint green. 
•  Label drums with rub on letters purchased from your local hobby shop.
• Display!

Making Walls

Here's on way on how to make a stone wall:

1. Items required: gravel, silicone RTV sealer (or caulking, or something similar), piece of wood as long as, and slightly wider than the section of wall you wish to build.
2. Glue the pieces of gravel to the wood using the silicone. Mix and match (like a puzzle) the gravel to give straight lines on the sides and eventually the top. The wall will get heavy enough to cause distortions if you try to do it all at once. Do about an inch or two high along the entire length of the wall and then let the silicone cure. Continue to add an inch or two in height every day until the wall is high enough. 
3. If you need a really thick stone wall, use a piece of Styrofoam and glue the gravel to the sides and top of the Styrofoam. The wall will still get heavy but the Styrofoam will help a bit!
4. If you fit the gravel together tightly, you can make a replica of a mortar-less stone wall. If you prefer to make a replica of a wall with mortar between the rocks, make the wall as noted above and let the silicone cure. After the silicone cures, run a bead of Elmer's or another hobby glue along the joints between the gravel and then sprinkle fine sand over the glue. After that dries brush off the excess sand. You can get fine sand in different colors from a hobby store that carries supplies for sand art.
5. Build the wall up to the end edges of the wood. This will allow you to make several sections of wall that will be smaller, easily stored and allow configuration changes for dioramas, etc. If you need to make a 90 degree corner, you can either make the corner as part of one section of wall, or make the wood ends as wide as the wall instead of a bit wider.
6. To finish off the sections of wall, glue dirt, model railroad ground cover, etc to the wood at the base of the wall. Also glue in a few bits of straw to simulate taller growing grasses, etc. -- Rob S.

Making Barbed Wire

How to Make Barbed Wire: Items needed: 30 gauge wire (found in hobby stores, Wal-Mart, etc - used for flowers & stuff), twigs (about 1/2 inch diameter), piece of wood (about 1/2 inch thick, plywood OK), glue, locking pliers or forceps, wire cutters, drill & bits, saw, rag.

1. Determine how much distance you want between fence posts. Also determine how high you want the fence to be (about 6 inches for a regular fence, about 16 inches or higher if you want to build a POW stockade).
2. Cut your wood about 2" - 3" wide and 2" - 3" longer than you want the fence section to be.
3. Cut the twigs to length, adding about 1/2 inch (or the thickness of your wood).
4. Drill 1/2 inch holes in the wood where you want the fence posts to be.
5. Glue fence posts into holes in wood. Set aside to dry thoroughly.
6. Cut a piece of the wire two times the distance between the fence posts, plus an extra 12 inches. For a 12 inch length of fence the length will be 36 inches (12 inches times two plus 12 more inches). The extra 12 inches of wire will be used to wrap around the fence post and secure the wire to the post.
7. Place the two ends of the wire together and pull the wire tight to form a doubled piece of wire.
8. Using the vice grip pliers or forceps, grab each end of the doubled wire and twist the wire. Keep twisting the wire until it has about 1/8 inch or less between the places where the wire crosses over itself.
9. Place the rag over the doubled & twisted wire and firmly pinch the wire (I fold the rag several times to give me a thicker pad of protection). Starting at one end of the twisted wire, squeeze and pull the rag along the length of the twisted wire (similar to closing a "zip-lock" bag). Do this a couple of times. What we are doing is setting the twist into the wire so when we remove the pliers/forceps the wire won't untwist by itself. You MUST use a rag or something similar because the wire will cut through skin if you try this with unprotected fingers!!! Set the wire aside.
10. Repeat steps 6 through 9 until you have one strand of wire for every inch to inch-and-a-half of post height.
11. Cut a bunch of 2" lengths of wire. Keep cutting, you'll need a BUNCH of these!
12. Take the 2" pieces of wire and wrap them around the twisted wire sections. Start about 3 inches from one end and wrap them every inch. Make sure you wrap them tightly against the twisted wire, and wrap each one about 4 times around the twisted wire. These will be the "barb" part of your barbed wire fence. Don't worry about how long the ends are, just wrap the entire length of twisted wire. Do this for all pieces of twisted wire you made in steps 6 - 9.
13. Take your wire cutters and snip off the extra length on each end of the barbs. Real barbs are about 1/2 inch long. I make the barbs a bit longer than normal (scale-wise) because they look better (i.e. you can see them!). Play around with the final length of your barbs and make them as long as you think looks good.
14. Wrap the ends of each section of barbed wire around the fence posts and twist the wire back on itself to hold the wire onto the post. BE CAREFUL - the barbs are REAL! ;-) Snip off the extra wire. Do this on both sides of the fence section, starting about 1 inch from the wood and working up about an inch for every piece of wire.
15. The fence section is finished. I make mine about 12 inches long so I can move them around easily. You can make them any length and any height. A good way to finish off the wooden bottom is to glue dirt, flocking, etc to the wood to simulate dirt, grass, etc. Need something besides fences? Make the sections of barbed wire and then coil them up to simulate coiled barbed wire. Use small (about 1 inch tall) pieces of smaller twigs glued into a wider section of wood, string the barbed wire between them and create "tanglefoot." Let your imagination roam wild! Good luck & have fun! -- Rob S

To see the complete article CLICK HERE
GI Joe® is a trademark of Hasbro, Inc.


We hope you enjoyed this post!  Let us know what you think or share any tips or ideas in the comments below.

Check out our Website: CLICK HERE
Like us on Facebook: CLICK HERE

thanks for reading this blog post and we look forward to your sharing with us.

Happy Hobbying!!

Valerie